StarQuest USA

Open to all Starion and Conquest enthusiasts.
 
HomeRegisterLog in

Share | 
 

 Fucked up pulley

View previous topic View next topic Go down 
AuthorMessage
Dz Nutz
Administration
Administration
avatar

Posts : 294
Join date : 2010-11-24
Age : 42
Location : Sycamore, OK

PostSubject: Fucked up pulley   2011-01-21, 7:58 pm

Back to top Go down
http://starquestusa.forumotion.com
caliber308
14a
14a
avatar

Posts : 42
Join date : 2010-11-27
Location : Paulden,AZ

PostSubject: Re: Fucked up pulley   2011-01-21, 10:20 pm

Do you have Metal Eating Mice in your neighborhood????

Bill
Back to top Go down
Dz Nutz
Administration
Administration
avatar

Posts : 294
Join date : 2010-11-24
Age : 42
Location : Sycamore, OK

PostSubject: Re: Fucked up pulley   2011-01-22, 8:48 am

I think it may have had a hairline fracture from a couple years ago when I left the wrench on the crank & started it. From then it was just time before she unwound I'm afraid
Back to top Go down
http://starquestusa.forumotion.com
caliber308
14a
14a
avatar

Posts : 42
Join date : 2010-11-27
Location : Paulden,AZ

PostSubject: Re: Fucked up pulley   2011-01-22, 5:35 pm

@Dz Nutz wrote:
I think it may have had a hairline fracture from a couple years ago when I left the wrench on the crank & started it. From then it was just time before she unwound I'm afraid

That will do it. Your lucky it didn't fly off & do more damage.

Bill
Back to top Go down
Dz Nutz
Administration
Administration
avatar

Posts : 294
Join date : 2010-11-24
Age : 42
Location : Sycamore, OK

PostSubject: Re: Fucked up pulley   2011-01-23, 9:01 am

Replaced the pulley to find the crank pulley split. FUCK. So I go digging through my boxes of parts in the garage just to be sure I do not have one of those either. BAM! I lift an oil pan out of a box & there sits an 89 crank pulley along with an 89 WP pulley & PS pump. So I am upgrading to the 10mm belts today! Also replacing the seal while the pulley is out.
Back to top Go down
http://starquestusa.forumotion.com
UlrichWolf
Moderation
Moderation
avatar

Posts : 49
Join date : 2010-12-02
Age : 42
Location : Kansas

PostSubject: Re: Fucked up pulley   2011-01-23, 11:04 am

Fuckin' A!

Tim
Back to top Go down
Dz Nutz
Administration
Administration
avatar

Posts : 294
Join date : 2010-11-24
Age : 42
Location : Sycamore, OK

PostSubject: Re: Fucked up pulley   2011-01-23, 1:05 pm

Here is the old ones off the car. 8mm belt size while my alternator has a 10 mm pulley on it. There is a bit of the tear that looks old & a bit rusty so I think it was cracked from earlier.








Here are the new ones going to go on the car. 10mm all the way around along with a new seal on the timing cover.

Back to top Go down
http://starquestusa.forumotion.com
Dz Nutz
Administration
Administration
avatar

Posts : 294
Join date : 2010-11-24
Age : 42
Location : Sycamore, OK

PostSubject: Re: Fucked up pulley   2011-01-29, 11:20 am

Well it looks like I need to replace the water pump. It is making noise now & beginning to seep out the weep hole. I am not surprised because of the damage to the pulley.

Found a NEW one through NAPA for less than $50 so I am going to do that. While I am at it I think I will put my other front cover on since I have the gaskets for it. Gimme a chance to peek in at the timing chains & such too.
Back to top Go down
http://starquestusa.forumotion.com
Sponsored content




PostSubject: Re: Fucked up pulley   

Back to top Go down
 
Fucked up pulley
View previous topic View next topic Back to top 
Page 1 of 1
 Similar topics
-
» Pulley Question
» Repacing my Alt. Tensioner pulley assbly broke, now what?!
» Broken SC Pulley?
» Write-Up: How to Remove/Install SC Pulley
» wtb 4ac crank pulley asap

Permissions in this forum:You cannot reply to topics in this forum
StarQuest USA :: Community :: ALMOST Anything Goes-
Jump to: